Das Wappen LQ verfügt über ein Leistungsmodul mit Bi-Amping-Funktion mit 200 Watt dynamischer Spitzenleistung für den Tieftöner und 70 Watt dynamischer Spitzenleistung Leistung für den Hochtöner des Kompressionstreibers, beide mit Leistungsverstärker Kompression. Mit einem 10 "Premium-Tieftöner und dem CrestHF -1 Komprimierungstreiber für den LQ 10P symmetrische Line-Level-Eingängemit Lautstärkeregler und Loop-Thru-Buchs
Merkmale:
- Bi-verstärktes System mit 200 Watt Gesamtleistung!
- 10 "Premium-Hochleistungs-Tieftöner mit großer Reichweite
- Maximaler Schalldruckpegel von mehr als 120 dB bei Musik!
- Symmetrische Eingänge mit 1/4 "Klinken- und M / F-XLR-Line-Pegel
- Das Horn mit quadratischer Halsgeometrie ermöglicht eine außergewöhnlich gleichmäßige Ansprache und präzise Musterkontrolle
- Link Out / In-Buchsen ermöglicht die Verbindung mit der zweiten Einheit
- Oberer Handgriff
Technische Daten:
- Enclosure: Crest LQ 10P (domestic)
- Frequency response: 80 Hz to 20 kHz
- Low frequency limit (-3dB point): 80 Hz
- Useable low frequency limit (-10 dB point): 63 Hz
- Internal power amplifier (@120 VAC line): Woofer - 200 Watts peak dynamic power 150 Watts at clipping, Tweeter - 70 Watts peak dynamic power 50 Watts at clipping
- Nominal sensitivity (IW @Im, swept sine input in anechoic environment): 96 dB
- Maximum sound pressure level @ Im: 120 dB music peak
- Nominal radiation angle: 90° horizontal by 4° vertical
- Transducer complement: 10" premium, heavey-duty, long throw weather-resistant woofer and Crest HF-I 1.4" titanium diaphragm comptession driver tweeter
- Box tuning frequency (Fbox): 76 Hz
- Electroacoustic crossover frequency: 2 kHz
- Crossover type: Internal electronic two-way crossover with CD horn EQ, level matching, active bass boost and subsonic filtering. The unit`s horn is spatially aligned with its woofer, so there is no need for phase alignment or time delay of the signals.
- Crossover slopes: 18 dB/octave (third order) low pass. 18 dB/octave (third order) high pass, both with staggered poles and driver EQ.
- Input Connections: One combo female XLR-1/4" phone jack and one male XLR, all providing balanced operation in parallel. Also has a ¼" phone jackbased loop-thru that allows one other LQ unit to be linked to the first unit for signal source and volume control.
- Enclosure materials and finish: Injection-molded high-impact polypropylene of a ¼" nominal thickness with internal ribbing and bracing, textured finish, and a UL flame rating. Molded material is dark gray.
- Mounting: Fliying via Omnimount 75 series (top or bottom of cabinet) and four rubber feet for floor use. Arry brackets are available.
- Maße (B x H x T): vorne 35,5 x 48 x 34 cm, hinten 21 x 44 x 34 cm
- Gewicht: 14,10 kg
Electronics and Amplifier
- Electronic input impedance (nominal): Primary balanced input: 10 k Ohms unbalanced, 20 k Ohms balanced. Linl Thru Input: High-Z
- Infrasonic filter protection: 36 dB/octave roll-off
- For both power amps: Nominal Amplifier Frequencey Response: +0,-1 dB from 10 Hz to 30 kHz
- Hum and noise: Greater than 90 dB below rated power
- Clipping prevention compression dynamic range: Greater than 14 dB
- THD and IM: Typically less than 0,1%
- Woofer power amp: Damping Factor: Greater than 100 @ 1000 Hz, 8 Ohms
- Nomonal power requirements of LQ 10P system (domestic): 100 Watts nominal, 120 VAC, 60 Hz
Hinweise zum Gebrauchtzustand und Lieferumfang:
- Gebrauchsspuren vorhanden, siehe Bilder
- Technisch einwandfrei, Funktion geprüft
- 1 x Crest Audio LQ 10B Lautsprecher PAAR gebraucht